2005 Kia Spectra former Wheel drive Automatic 72000 milesSpeedometer and odometer has stopped working. Should I reset the computer system by disconnecting battery? where is the sensor located so i can obtain a intuitive to examine for the obvious?


You are watching: 2006 kia spectra speed sensor location

*

The vehicle speed sensor going out will reason the speedometer no to work. The connector is situated at the read the the engine near the bellhousing but the sensor is down close to the last drive axle output. This overview will present you whereby the connector is simply follow it under to the sensor. (Below)Please permit us understand if you need anything else to acquire the problem fixed.Cheers, Ken
*

*

Speedometer stopped working completely kinda simply figured it to be the speed sensor. Simply would choose to know exactly how to change it or if maybe thats no the problem.
*

It commonly is the cause however it could also be the wiring and only testings would confirm it. Instead of is a simple job. Disconnect the coupler, remove the holding bolt and twist the sensor out.
*

walk you replace the car speed sensor? Does her speedometer work correctly?Yes, it could make a difference but it would collection a abs code.Roy
Yes changed speed sensor and yes speedometer functions perfectly. Also readjusted safety switch and there are no ABS codes just the P0501 code
check engine light come on. DTC revealed p0501 vss. I recently lost my front right tire because of some shrapnel top top the road. I changed the tire, but the engine light appeared after the incident. I noticed a cable hanging down near the prior tire. I"m suspect this wire is the vss and am wonder if this is other I can fix myself? Is over there a way to reattach this wire? i was looking online for a diagram and also any helpful information. Deserve to you help?


See more: How To Get Bigger Breast In 5 Minutes, The Surprising Answer

Ok, most likely it is a abs issue. The an initial thing i would carry out is adjust the tires come the exactly size.GENERAL description The Wheel rate Sensor (WSS) generates a waveform with a frequency proportional come the rate of the vehicle. The signal generated by the WSS notifies the PCM not only if the automobile speed is low or high but additionally if the auto is or is no moving. The PCM provides this signal to regulate the fuel injection, ignition timing, transaxle shift scheduling and torque converter clutch scheduling. The WSS signal is likewise used to detect rough roadway conditions.DTC description The PCM evaluates engine speed and mass air flow if there is no vehicle speed signal. This evaluation of both values will detect open up circuit or quick circuit errors on the wheel speed sensor. The PCM set DTC P0501 if there is no vehicle speed signal native wheel speed sensor if both engine speed and mass air flow are greater than predetermined threshold during the predetermined time.DTC Detecting ConditionZoomSized because that PrintZoomSized because that PrintMONITOR DTC STATUS attach Connect scan tool and also select "Diagnostic trouble Codes(DTCs)" mode.Press F5(INFO) to choose DTC details from the DTCs menu.Confirm that "DTC Readiness Flag" indicates "Complete". If not, drive the automobile within conditions provided in the freeze framework data or enable conditions.Read "DTC Status" parameter.Is parameter presented "History(Not Present) fault"?NOTE: background (Not Present) fault : DTC emerged but has been cleared.Present error : DTC is developing at present time.YES - error is intermittent, brought about by negative contact in the sensor's and/or PCM's connector or was repaired and also PCM memory was not cleared. Thoroughly check connectors because that looseness, negative connection, bending, corrosion, contamination, deterioration, or damage. Repair or change as necessary and go to "Verification of vehicle Repair" procedure.NO go to "Monitor Scan device Data" procedure. walk to "Signal Circuit Inspection" procedure.MONITOR SCAN device DATA With car raised top top a lift, begin the engine and place transaxle in Drive. Let automobile idle and verify speedometer suggests approx. 10 km/h or more(6 mph or more) top top the tool cluster.Connect Scantool and select ABS system.Monitor the "WHEEL SPD SENSOR-FR" parameter ~ above the present data list.Specification : 10 km/h or more(6 mph or more)Is value within the specification?YES - Wheel rate sensor is OK. Go to "Signal Circuit Inspection" procedure.NO examine for open up or brief circuit between wheel speed sensor(FR) and also ABS(or ESP) manage module.If troubles are found, repair as necessary and go come "Verification of automobile Repair" procedureIf OK, check wheel speed sensor(FR) as follow :Gap between ABS sensor and also trigger wheel (Air space : 0.3 - 1.1 mm (0.011 - 0.043 in ))Trigger wheel problem - Sensor resistance : Approx. 1,300 - 1,500 Ohms at 20 levels C (68 levels F)Replace wheel rate sensor together necessary and also go come "Verification of automobile Repair" procedure.SIGNAL CIRCUIT INSPECTION ZoomSized because that PrintCheck for open up in circuit.Ignition "OFF".Disconnect PCM and also ABS regulate Module connectorsMeasure resistance between terminals 39 the the PCM exploit connector and also 3 of the ABS control Module exploit connector(W/ABS)Specification : Approx. 0 Ohm Is resistance within the specification?YES - walk to following step.NO - Repair as necessary and go to "Verification of auto Repair" procedure.ZoomSized because that PrintCheck for quick to ground in circuit.Measure resistance between terminal 39 the the PCM harness connector and chassis ground.Specification : InfiniteIs resistance within the specification?YES - check for negative connection in between PCM and also component: backed the end terminal, not correct mating, damaged locks or poor terminal to wire connection. Repair together necessary and go come "Verification of vehicle Repair" procedure.NO - Repair together necessary and also go come "Verification of auto Repair" procedure.VERIFICATION OF car REPAIR after a repair, the is necessary to verify the the fault has actually been corrected.Connect scan tool and also select "Diagnostic problem Codes(DTCs)" mode.Press F5(INFO) and confirm that "DTC Readiness Flag" shows "Complete". If not, drive the auto within conditions provided in the freeze structure data or enable conditions.Read "DTC Status" parameter.Is parameter displayed "History(Not Present) fault"?YES - device performing to specification in ~ this time. Clean the DTCNO - walk to the applicable troubleshooting procedure.Schematic DiagramZoomSized for Print© 2016 ALLDATA LLC. All legal rights reserved. Terms and Conditions