Changing the serpentine belt on your Hyundai automobile is crucial part of keeping the engine. If the belts become damaged or worn, it have the right to fail or break while you room driving the car. Since the belt transforms the alternator, water pump and power steering in your car, fail of the belt can reason the engine to overheat, be difficult to command and allow the battery to discharge an extremely rapidly. Inspect the belt often. Every time you adjust the oil girlfriend should inspect it.


Under The Hood:

How to adjust a Serpentine Belt ~ above a Hyundai

Locate the tensioner sheave on the former of your engine. The tensioner looks prefer the other pulleys however is placed on a spring loaded arm.

You are watching: 2004 hyundai sonata serpentine belt replacement


Place a socket and also ratchet ~ above the bolt in the facility of the tensioner pulley and move the ratchet counterclockwise to relieve the tension on the belt. Slide the old belt turn off the pulleys and also slowly allow the tension earlier on the tensioner.

Position a new belt top top the pulleys making certain that you monitor the same path with the brand-new belt that the old one followed. If the serpentine belt it s okay reversed top top the pulleys, the accessories will certainly spin the dorn direction and also can it is in damaged.

Move the ratchet ~ above the belt tensioner counterclockwise again and slide the belt top top the tensioner. Gradually move the ratchet clockwise to relax the tensioner and also tighten the belt.

Start the engine and watch the belt. Visually verify that the belt is running true throughout all the pulleys.


Items you will need

Socket collection w/ratchet


How to replace the Serpentine Belt top top a 2001 Hyundai Santa Fe

Open the hood of your Santa Fe and locate the negative battery cable at the battery. Loosen the retaining bolt the secures the cable finish to the battery terminal utilizing a wrench, and then eliminate the battery cable native the terminal.

Position yourself in front of the truck and look in ~ the front of the engine just behind the radiator, in the center of the engine. The serpentine-belt tensioner sit on the engine just below the power-steering pump.

Place a socket and also breaker bar ~ above the bolt in the center of the idler wheel on the belt tensioner. Turn the tensioner clockwise, publication the tension from the belt. Remove the belt and discard it, then turn the tensioner counterclockwise come the totally free arm position.

Install a new belt end the pulleys top top the front of the engine, leave it turn off the tensioner for now. Turn the tensioner clockwise, climate slide the belt onto the idler pulley on the tensioner and also rotate the tensioner counterclockwise, enabling the tensioner to tighten the belt.

Remove the socket and also breaker bar from the tensioner, climate move ago to the battery. Download the negative battery cable top top the negative terminal and also tighten the retaining bolt through a wrench. Close the hood.


Items you will need

Wrench set

Socket set

Breaker bar


How to replace a Serpentine Belt ~ above a 2004 Hyundai

Removing Old Belt

Remove the engine cover utilizing a socket wrench and also then set aside. Make note of the belt routing. Examine for a belt diagram routing sticker in ~ the engine compartment or the owner"s manual. If no chart exists, draw your own in-depth diagram before you remove the belt.

Insert the serpentine belt tool into the square hole of the tensioner pulley. Standing in former of the engine compartment, grab the handle of the tool and push or pull together required, releasing tension from the tensioner pulley. If holding the anxiety off the belt, grasp the serpentine belt and also remove that from one pulley. Then release the stress and anxiety from the tensioner pulley.

Grab the loosened serpentine belt from roughly other pulleys and also remove the from engine compartment.

Installing brand-new Belt

Compare the brand-new belt length versus the old belt. The brand-new belt have to not be longer. It may be slightly shorter as the old belt has actually stretched end time.

Install the brand-new belt complying with belt diagram. Beginning with the lowest pulley, route the belt up and around the pulleys until the belt slack is gone. Take the serpentine belt tool and push or traction as compelled to release stress from the tensioner pulley. Then finish routing the belt approximately the remaining pulleys.

Check for suitable installation of the serpentine belt. Verify the routing of the belt against the routing diagram. Remove the serpentine belt tool. Verify the belt lays focused on every pulley. Inspect for belt stress and anxiety by grabbing and also pulling ~ above the belt between two pulleys.

Perform operational test. Reinstall the engine cover and also start the engine. Hear for abnormal sounds or vibrations.


Items you will certainly need

Serpentine Belt Tool: #OEM27115

Socket wrench set


How to change the Serpentine Belt in a Hyundai Sonata

Find the tensioner. The serpentine belt tensioner is what hold the belt in location with the exactly tension: the is hosted to the engine by 2 bolts. Some define the Hyundai Sonata tensioner sheave as attached to a teardrop shape, v the bolts stop the structure to the engine.

Remove the 2 bolts close to the tensioner with your wrench (bolt size might vary by model). Take turn off the tensioner and also the belt.

Use a belt routing diagram or your own sketches to change the serpentine belt. This is helpful for part models: native the strength steering pump, the belt goes to the left that the idler pulley, climate over and also around the right side of the air conditioner compressor pulley, about the left side of the crank pulley, come the best of the tensioner pulley, and down to the alternator.

Replace the tensioner and also the new belt together. Mechanics introduce seating the belt on the tensioner before replacing the tensioner onto the engine fairly than trying come pry the belt over the pulley.

Tighten the two lock bolts that host the tensioner.

See more: Are Belly Button Piercing Bleeding After 2 Months ? Help!? Piercing Aftercare!

Check to view that the belt is seated correctly on every one of the pulleys. Run the engine and observe to examine for ideal installation.